High-entropy titanate pyrochlore as newly low-thermal conductivity ceramics

Low-thermal conductivity ceramics play an indispensable role in maximizing the efficiency and durability of hot end components. Pyrochlore, particularly zirconate pyrochlore, is currently a highly promising and widely studied candidate for its extremely low thermal conductivity. However, there are still few pyrochlores that offer both stiffness, insulation, and good thermal expansion properties. In this work, the solidification method was innovatively introduced into the preparation of titanate pyrochlore, and combined it with the compositional design of high-entropy. Through careful composition design and solidification control, the high-density and uniform elements distributed high-entropy titanate pyrochlore ceramics were successfully prepared. These samples possess high hardness (15.88 GPa) and Young’s modulus (295.5 GPa), low thermal conductivity (0.947 W·m^?1·K^?1), excellent thermal expansion coefficient (11.6 ×10^?6/K) and an exquisite balance between stiffness and insulation (E/κ, 312.1 GPa·W^?1·m·K), in which the E/κ exhibits the highest value among the current reported works.     

饱和块状混合回填土地基的一维固结分析

用块状渣土置换软弱地基和回填低洼谷地等是处置工程渣土的有效途径。为了分析饱和块状混合回填土地基的固结性状，运用混合物理论建立了其一维固结模型。首先，假定块状土固相和充填土固相之间满足等应变条件，获得了饱和块状混合回填土中各相应变与块状土孔隙变形和充填土孔隙变形的关系式。其次，在小应变条件下，根据自由能势函数方程建立了饱和块状混合回填土的一维线弹性本构方程，再结合达西定律和应力平衡方程获得了一维固结控制方程。再次，利用分离变量法得到一维固结解析解，通过退化本文模型与已有模型进行对比，验证了本文模型的正确性。最后，基于所得解析解，分析了充填土孔隙渗透系数、块状土孔隙渗透系数以及流体交换参数等因素对饱和块状混合回填土地基固结性状的影响。分析结果表明：充填土孔隙渗透系数对饱和块状混合回填土地基整体固结性状起主导作用；在固结初期，块状土超孔压会有一定程度的上升，且3个参数具有相似的作用机理。     

C105管桩混凝土设计参数取值的探讨

通过试验得出了C105混凝土100 mm×100 mm×100 mm立方体非标准试件抗压强度换算系数以及C105混凝土的标准方差和强度变异系数。采用理论计算,得到了棱柱体抗压强度与立方体抗压强度的比值α_c1,并与试验实测平均值进行了比较,验证了理论计算方法的可行性。此外,通过对比分析,探讨了直接外延法和引用公式法两种C105混凝土设计参数计算方法的正确性,研究结果可为C105管桩混凝土的设计和应用提供参考。     

Method for calculating horizontal drain induced non-linear and large strain degree of consolidation

Consolidating dredged clay slurries using a combination of vacuum pressure and prefabricated horizontal drains (PHDs) is widely used in practice. This is a large strain problem, but there is no existing large strain theory for PHD induced consolidation. A method with explicit equations has been proposed to consider both mechanical and geometrical non-linearities in analyzing PHD induced consolidation. The method considers stepwise variation of properties using imaginary time concept. An imaginary time is determined by the condition of continuity of degree of consolidation before and after changing the properties. Then the method was applied to analyze a large scale model test of vacuum consolidation with PHD. Two analyses were conducted. One considered both the mechanical and geometrical non-linearity (large strain), and another only considered mechanical non-linearity (small strain). The results of large strain analysis agree with the measured settlement curve and excess pore pressures well. While the small strain analysis under-estimated the rate of consolidation significantly. The results from this study indicate that for analyzing PHD induced consolidation of clay slurries considering the effect of large strain is important, and the proposed method can be a useful design tool.     

建筑物掏土纠倾法单孔与多孔塑性区特性研究及工程应用

在建筑物水平掏土纠倾工程中，掏土孔间距是影响纠倾工程安全与工期的重要因素。为了快速准确地确定纠倾工程中的水平掏土孔间距，研究了单个掏土孔和多个掏土孔情况下孔周边土体塑性区发展特性。利用土体塑性力学分析计算得到了单孔下的孔周土塑性区半径，而后通过有限元模拟得到孔周土体塑性区半径的数值解，将孔周塑性区半径解析解与数值解进行了对比。并通过有限元数值模型研究了多个掏土孔相互影响情况下的塑性区发展规律，以孔间土体塑性区贯通时的距离作为掏土孔间距。考虑土体参数随机特性的影响，研究不同上部荷载作用下掏土孔间距的取值变化规律，上部面荷载与地基承载力特征值比值用p表示，孔间距与掏土孔直径比值用n表示。研究发现：多孔塑性区半径（孔间塑性区贯通时）是单孔塑性区半径的1.3倍左右;标准化荷载p与孔间距比值n二者呈线性关系;通过不同土体参数及上部荷载的不同情况下的p-n曲线，给出了掏土孔间距建议值。同时，将研究结果与三个实际工程进行对比，发现p-n曲线法与实际结果更为接近。     

基于音频特征的工程车辆工况识别研究

高效率地使用工程车辆是工程项目管理中节约成本的有效方法，无人监管环境下工程车辆的工况识别，是实现工程车辆高效率使用的有效手段。目前以GPS等技术为核心的车辆智能管理系统未对工程车辆进行工况识别，提出一种基于GRU循环神经网络的工程车辆工况识别方法，通过对工程车辆在不同工况下产生的音频信号进行分析，从中提取Mel倒谱系数作为主要特征，构建GRU循环神经网络模型进行训练和识别。实验结果表明，该方法可以实现对工程车辆工况的有效识别。     

High-performance Pb(Ni1/3Nb2/3)O3-PbZrO3-PbTiO3 ceramics with the triple point composition

Ternary 0.552Pb(Ni_1/3Nb_2/3)O₃-xPbZrO₃-(0.448-x)PbTiO₃ (PNN-PZ-PT) ceramics near the triple point compositions were fabricated by an improved two-step sintering method. The triple point composition 0.552PNN-0.135PZ-0.313PT ceramic has outstanding piezoelectric performance with piezoelectric coefficient d₃₃ = 1200 pC/N. Its easy fabrication and low cost make this piezoelectric material an excellent candidate for high sensitivity sensors and ultrasonic transducers. The evolution of domain structures for ceramics with composition near the triple point provides deeper insight into the mechanism of ultrahigh piezoelectric properties of PNN-PZ-PT ceramics.     

Strain mediated enhancement in magnetoelectric properties of sonochemically synthesized piezoelectric and piezomagnetic composites

Materials with magneto-electric (ME) properties are of great importance because of their demand in electronic industries. Three dimensional nano-particles of the ME-composites having the general formula (1-x)CoCr_0.3Fe_1.7O₄(CCFO)+(x)BaTiO₃(BTO) (x = 0.0, 0.2, 0.4, 0.6, 0.8 and 1.0) were obtained by comprising the piezoelectric-BTO and piezomagnetic-CCFO phases. The individual phases of CCFO and BTO were synthesized separately by ultrasonic irradiation assisted sonochemical and sol-gel routs. X-ray diffraction patterns (XRD) confirmed the well-crystalline nature of both the phases. BTO and CCFO phases were under tensile strain as confirmed by the variation in lattice constants with varying proportion of BTO and CCFO. An energy-dispersive X-ray spectroscopy spectrum confirmed the phase purity of the samples and stoichiometric concentration of elements. Magnetic properties were investigated by M ? H loop measurements and dielectric properties by using RF impedance analyzer. Dielectric constant increased with the increasing percentage of BTO. The maximum value of ME coefficient (24.7 mV/cm?Oe) is observed for the 60%CCFO+40%BTO sample. The obtained results were discussed in the light of grain size, strain and the basic properties of the individual phases. The prepared materials can be applicable in electronic devices where high magneto-electric coefficient is desirable.